Skip to main content
Version: Ver.4.10

Communication Settings

Importing an LDF into Catalog and configuring communication in Device Window are separate operations. Do not assume that importing alone applies bitrate or per-ID DL settings. For change confirmations when adopting definitions in Simulation, see Pre-transmission Checks.

Use Device Window to configure communication settings for the connected MicroPeckerX. Always configure these settings before starting monitoring.

Basic Operation​

This example configures Ch1-1 of an S810-MX-LN1. Configure each target Ch to match the connected LIN bus.

  1. Open Device Window
    Select Device Window from the menu or toolbar.
Device Window with Ch1[1300101] selected, showing Model S810-MX-LN1 and LIN Standard and DIO/AD Standard Full Licenses on the right

Figure 1: Checking the connected device Model and licenses.

  1. Select the channel to configure
    Select Ch1-1 in the device list on the left. Check that Model under Device Info is S810-MX-LN1 and that Protocol Setting on the right shows LIN settings for Ch1-1. When using multiple MicroPeckerX units, configure each Ch used to monitor a LIN bus.

  2. Select the revision and baud rate Under Protocol Setting, select the connected LIN bus revision and bitrate using Revision and Baudrate. Figure 2 shows Revision 2.2A and Baudrate 19200bps.

LIN settings for Ch1-1: Revision 2.2A, Baudrate 19200bps

Figure 2: LIN revision and bitrate settings.

  1. Select bit widths Select each bit width on the BitWidth tab under Protocol Setting. Figure 3 shows Synch Break 13, Header 35 bit, DL 2 for checking displayed lengths, Max 89.6 bit, and Total 68 bit.
BitWidth tab: Synch Break 13, Header 35 bit, DL 2, Max 89.6 bit, Total 68 bit

Figure 3: Example BitWidth tab settings.

  1. Configure ID definitions On the ID Definition tab, set data length and checksum type for each ID. Figure 4 shows the 10- group, with DL 2 and Checksum Type Classic for ID 10 (hexadecimal 0x10). Check each ID's actual data length on this tab.
ID Definition tab, 10- group: ID 10, DL 2, Checksum Type Classic

Figure 4: Data length and checksum type for each ID.

  1. Set wakeup pulse width and sleep time Configure wakeup pulse width and sleep time on the Wakeup/Sleep tab. Figure 5 shows Wakeup Width 400 us, Wakeup Wait 0 ms, and Sleep Time 4 s.
Wakeup/Sleep tab: Wakeup Width 400 us, Wakeup Wait 0 ms, Sleep Time 4 s

Figure 5: Wakeup and sleep settings.

Communication settings for the LIN bus are now complete.


Device Window Screen Description​

Figure 1 shows the device name Ch1[1300101] selected on the left and licenses displayed on the right. Selecting Ch1-1 below it switches to Protocol Setting as in Figure 2.

Item nameDescription
Device List
(device list on the left)
Displays a list of MicroPeckerX units recognized by MicroPeckerX Control Software.
You can enable/disable each channel by toggling the checkbox on the left of each channel.
Up arrow buttonSwaps the selected MicroPeckerX channel position with the one above it in Device List.
For example, if a unit assigned to Ch2 is selected, it will be moved to Ch1 (the Ch1 unit moves to Ch2).
Down arrow buttonSwaps the selected MicroPeckerX channel position with the one below it in Device List.
For example, if a unit assigned to Ch2 is selected, it will be moved to Ch3 (the Ch3 unit moves to Ch2).
Device InfoSerialDisplays serial number of the MicroPeckerX selected in Device List.
ModelDisplays model name of the MicroPeckerX selected in Device List.
Blink LED buttonBlinks green and yellow LEDs of the MicroPeckerX selected in Device List.
Click again to stop blinking.
This helps identify the selected device.
Device Refresh] buttonRe-detects MicroPeckerX units connected to the PC.
Information / settings area on the right
(Protocol Setting when a Ch is selected)
If a Serial row is selected in Device List, registered licenses on MicroPeckerX are shown.
If a channel row is selected, the communication setting screen is shown.
If an unrecognized device is selected, No Device is shown.

Protocol Setting​

Use Revision and Baudrate in Figure 2 and the settings tabs in Figures 3–5.

Item nameDescriptionAdditional information
Protocol SettingDisplays information for the selected channel.
RevisionSets LIN revision. Select from:
1.3, 2.0, 2.1, 2.2, 2.2A
BaudrateSets communication baudrate. Select from:
500, 600, 1k, 1200, 2400, 4800, 5k, 9600, 10k, 10417, 14400, 15k, 19200, 20k, 25k, Custom [bps]
Selecting Custom displays a numeric input field to the right of Baudrate. Enter the connected LIN bus bitrate in bps (range: 500–20000). The 9600 in Figure 6 is an example.
Ch1-1 LIN settings with Baudrate Custom and 9600 bps displayed
Figure 6: Bitrate input field when Custom is selected.
Setting tab switchClick the BitWidth, ID Definition, or Wakeup/Sleep tab to switch the displayed settings.
For details on each tab, see:
BitWidth, ID Definition, Wakeup/Sleep
Default All buttonResets Protocol Setting values for the selected channel to defaults.
See Device Setting Defaults.

BitWidth Tab​

The BitWidth tab configures the bit widths between fields in the header and response sections.

See Figure 3 for the screen.

Item nameDescription
Sync BreakSets bit width of header break field. Range: 10-26.
Sync Break DelimiterSets bit width between break field and sync byte field. Range: 1-20.
Header SpaceSets bit width between sync byte field and protected field. Range: 0-20.
Inter Frame Response SpaceSets bit width between header and response. Range: 0-20.
Inter Byte SpaceSets bit width between data bytes, and between data and checksum in response. Range: 1-20.
[Default buttonResets only BitWidth tab settings of the selected channel to defaults. Revision, baudrate, and other tabs are unchanged.
See Device Setting Defaults.
HeaderShows header bit length based on current bit-width settings. Values update immediately when any bit width is changed.
If header length exceeds LIN limit (47.6 bits), Exceeds Max Header Length! is shown. Monitoring can still be started.
DLWhen DL (data length) is selected from pull-down (1-8), LIN max frame bit length is shown in Max, and calculated frame bit length based on current settings and DL is shown in Total. Values update immediately when bit width or data length changes.
If Total exceeds Max, Exceeds Max Frame Length! is shown. Monitoring can still be started.
Max
Total

ID Definition Tab​

The ID Definition tab configures data length and checksum type for each ID.

See Figure 4 for the screen.

ItemDescriptionAdditional information
ID definition tableDLDisplays data length for each ID.To change data length, use DL Setting.
DL SettingSets data length for each ID. Leftmost cell means 1, rightmost means 8. Click a cell to change data length.
When data length changes, DL display is updated.
Checksum TypeSets checksum type. Click Classic or Enhanced.
ID number tab
(00, 10, 20, 30)
Click tab to switch the top ID shown in the ID definition table. For example, clicking 10- makes top ID 10H.
On LIN1.3Sets ID definition behavior for LIN revision 1.3.
Fixed: fixed to standard ID definition (same as defaults).
Edited: editable in ID definition table.
This setting is unavailable for revisions other than 1.3 (treated as always Edited).
[Default buttonResets only ID Definition tab settings of the selected channel to defaults. Revision, baudrate, and other tabs are unchanged.See Device Setting Defaults.

Wakeup/Sleep Tab​

The Wakeup/Sleep tab configures wakeup signal transmission width, conditions for entering sleep mode, and other settings.

See Figure 5 for the screen.

ItemDescriptionAdditional information
Wakeup WidthSets wakeup signal transmission width in microseconds. Pull-down values:
50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 950, 1000, 2000, 3000, 4000, 5000, 6000, 7000, 8000, 9000, 10000
Unavailable on revision 1.3 (fixed to 8-bit length).
Wakeup WaitSets wait time (ms) after receiving wakeup signal until LIN schedule starts (resume from sleep). Range: 0-100.Applies only to master node.
Sleep TimeSets LIN bus idle time (seconds) before automatic transition to sleep mode. Pull-down values:
4, 5, 6, 7, 8, 9, 10
Unavailable on revisions 1.3 and 2.0.
Revision 1.3: follows Sleep by 25,000bit Idle (LIN 1.3 Only).
Revision 2.0: fixed to 4 seconds.
Sleep by 25,000bit Idle(LIN 1.3 Only)For revision 1.3, sets whether to auto-transition to sleep mode by idle time.
ON: auto-transition after 25,000-bit idle time.
OFF: no automatic transition to sleep mode.
Unavailable for revisions other than 1.3.

Device Setting Default Values​

Restores settings on each Protocol Setting tab for the target Ch to their installation defaults.

  • Restores Revision, Baudrate, BitWidth, ID Definition, and Wakeup/Sleep settings to their defaults.
  • Does not affect other Ch settings or settings in other windows.