Skip to main content
Version: Ver.4.10

GUI Application Message List

Messages Related to Signals and Communication Definitions​

Message / screenAction
Import ErrorsCheck Line, Column, and Description, correct the definition file, and reopen it. Import Errors
Signal Trigger reference is invalid. Select Signal again.Check Current Set, CH assignments, and the target signal, then select it again. Signal Trigger
No signals match this log. Open Signal Catalog to assign signals.Compare the analysis Set with the CH and frame conditions recorded in the log. When Analysis Is Unavailable
The monitoring buffer no longer contains data for this alert.Data from the alert time is no longer in the monitoring buffer. If a saved communication log is available, open it with its corresponding definitions. Saved Log Analysis
No LIN schedules in this source. Import an LDF with Schedule_tables using Signal Catalog.Check the Source LDF and whether Schedule_tables are registered. When No Schedules Are Displayed
Signal Catalog module is unavailable. Check SignalCatalog.dll beside MPXAnalyzer.exe.Check that SignalCatalog.dll is in the same folder as MPXAnalyzer.exe.

Signal CH Assignment and Synchronization Notifications​

Hover over a status bar notification to read its full text.

NotificationChecks and Corrective Actions
Signal Set suspended:The saved assignments cannot be resolved, so signals on the listed CH and derived signals that depend on unavailable inputs are suspended. Reconnect the devices used when saving, then select Device → Refresh.
Signal Set live mapping differs:A saved physical CH was recognized under a different CH number, which is now used for monitoring. Check the listed old and new CH numbers. To load Signal Monitor Setting from MPXXML, restore the CH configuration used when saving, then select Device → Refresh.
Loaded Signal settings pending device assignment:Synchronization between the signal settings loaded from MPXXML and the Current Set is pending. Before closing the application, reconnect all listed devices and internal CH and select Device → Refresh, or load different signal settings from Load Config.
Loaded Signal settings are not synchronized with the Signal Set.The loaded signal settings could not be applied to the Current Set. Check the devices and CH, then reload the signal settings from Load Config.

When Signal Monitor Setting cannot be selected in MPXXML

Language Setting Messages​

MessageCorrective Action
Could not save the display language. Windows error …Option stays open. Check the Windows error number and details in the message, resolve the cause, then click OK again.
The language was saved. Finish the current operation, then reopen Option to restart.Finish the current operation, reopen Option, and click OK to confirm the restart again.
Automatic restart failed. To apply the saved language, exit MicroPeckerX and open it again.The language has already been saved. Exit MicroPeckerX and open it again.

See Changing the Display Language for the full procedure.

Other Messages​

MessageDescriptionCorrective Action
A file necessary for startup is lacked.
Please reinstall control software.
A required startup file is missing. Please reinstall the control software.Reinstall the software because required runtime files are missing.
Buffer Over Run
Serial : 13XXXXX - X
State : XXX
Please re-connect all "MicroPeckerX" and refresh device.
Buffer overrun.
Serial : 13XXXXX - X
State : XXX
Reconnect all MicroPeckerX units and refresh devices.
Contact the developer/support.
Configuration Load Error.
Error : XXX
Configuration load error.
Error : XXX
Load the correct configuration file.
Configuration Load Error.
File not exists.
Configuration load error.
File not found.
Check that the configuration file name is correct.
Configuration Load Error.
File version is Illegal.
Configuration load error.
Invalid file version.
Load a configuration file in the correct format.
Configuration Load Error.
Folder is not exists.
Configuration load error.
Folder not found.
Check that the configuration file path is correct.
Configuration Load Error.
Illegal file format.
Configuration load error.
Invalid file format.
Load a configuration file in the correct format.
Configuration Save Error.
Folder is not exists.
Configuration save error.
Folder not found.
Check that the save destination path is correct.
Currently logging.
Are you sure you want to abort?
Logging is in progress.
Abort logging?
If logging is aborted, logs saved so far remain, but their contents are not guaranteed; for example, different channels may not contain logs up to the same time.
Currently under monitoring.
Are you sure you want to terminate?
Monitoring is in progress.
Stop monitoring?
-
Delete layout "XXX"?Delete layout "XXX"?-
Error of generating log replay buffer.Failed to generate log replay buffer.Ensure sufficient free disk space.
Failed to ready for log replay thread.Failed to initialize log replay thread.Remaining disk/memory resources may be insufficient. Use a higher-spec PC.
Failed to ready for monitor thread.Failed to initialize monitor thread.Remaining disk/memory resources may be insufficient. Use a higher-spec PC.
Failed to save the log.Failed to save log.Check whether the destination file is open in another application.
Internal Error
Serial : 13XXXXX - X
Error Code : XXX
State : XXX
Please re-connect all "MicroPeckerX" and refresh device.
Internal error.
Serial : 13XXXXX - X
Error Code : XXX
State : XXX
Reconnect all MicroPeckerX units and refresh devices.
Contact the developer/support.
It failed save error log.Failed to save error log.Check whether the destination file is open in another application.
Layout "XXX" already exists. Overwrite?Layout "XXX" already exists. Overwrite?-
Logging canceled.
The contents of the log file are not guaranteed.
Logging was canceled.
Log file contents are not guaranteed.
If logging is aborted, logs saved so far remain, but their contents are not guaranteed; for example, different channels may not contain logs up to the same time.
MicroPeckerX Communication Error
Serial : 13XXXXX - X
Error Code : XXX
Please re-connect all "MicroPeckerX" and refresh device.
MicroPeckerX communication error.
Serial : 13XXXXX - X
Error Code : XXX
Reconnect all MicroPeckerX units and refresh devices.
Contact the developer/support.
”MicroPeckerX Control Software” is already started.MicroPeckerX Control Software is already running.Multiple instances are not supported.
MicroPeckerX information acquisition failed.Failed to acquire MicroPeckerX information.Reinstall software because required files may be missing.
Monitor synchronization error.
Check the connection of the synchronous cable.
Monitor synchronization error.
Check sync cable connection.
When using multiple units, connect MicroPeckerX units with sync cables.
No setting information of the connected device.
Display the import dialog?
No setting information for the connected device.
Open import dialog?
If connected device information is missing in loaded settings, run import processing.
Set layout "XXX" as default?Set layout "XXX" as default?-
Setting Error.
[Simulation] The file of log replay is not load.
Serial : 13XXXXX
Ch : X
Setting error.
[Simulation] Log replay file is not loaded.
Serial : 13XXXXX
Ch : X
Load file before starting monitoring.
Setting Error.
[Trigger] In the ReTriggered mode, must set the start trigger.
Setting error.
[Trigger] Start trigger must be set in ReTriggered mode.
Enable start trigger in ReTriggered mode.
Setting Error.
The key trigger is duplicated.
Key:XXX
ChX-X XXX
ChX-X XXX
Setting error.
Duplicate key trigger.
Key: XXX
ChX-X XXX
ChX-X XXX
Check duplicate triggers and avoid assigning the same key.
Setting Error.
The log folder does not exist.
Setting error.
Log folder does not exist.
Check that the log save path is correct.
The Help file is not found.Help file not found.Reinstall software.
The log folder number has reached its maximum.Log folder number has reached the maximum.Select another destination folder.
There are no logging data.No logging data.Check cable connections; device-target connection may be incorrect.
Setting is cleared.
Are you sure?
Settings will be cleared.
Continue?
-
Delete the display filter?Delete display filter?-
Setting is cleared.
Are you sure?
Settings will be cleared.
Continue?
-
Delete the label filter "XXX"?Delete label filter "XXX"?-
Load Error.Load error.Check whether Hex/Binary format file content is correctly described.
Event Trigger is not selected. Are you sure to continue?Event trigger is not selected. Continue?If Event transmission mode is selected, configure an event trigger.
Log File Header Error.Log file header error.Load a log in the correct format.
Log file is not found.Log file not found.Check file path.
Log File Read Error. Line:XXXLog file read error. Line: XXXLoad a log in the correct format.
Setting is cleared.
Are you sure?
Settings will be cleared.
Continue?
-
The number of maximum transmission logs is exceeded.The maximum number of transmission logs has been exceeded.Log Replay displays a warning and loads up to the limit of 3 million records. Records beyond the limit are not loaded.
Are you sure to clear list?Clear list?-
Failed to save.Failed to save.Check whether the destination file is open in another application.
Log File Incompatible Error.Log file compatibility error.In Analyze tab of Analyze Window, MicroPecker format logs cannot be loaded directly. Load once in Ch Log tab, then run Mix.
Old Format Log Convert Result
Chx-x : Valid Log = XXX, Invalid Log = YYY
Old format log conversion result.
Chx-x : Valid Log = XXX, Invalid Log = YYY
Logs unsupported by MicroPeckerX are discarded. Check if invalid logs cause issues.
The same Ch can not be specified.The same channel cannot be specified.Set different channels for gateway source and destination.
There are no valid analytical logs.No valid analysis logs.This appears when logs are fully filtered out. Review filter settings.