Skip to main content
Version: Ver.3.03

Product Usage Flow

This section explains the end-to-end flow from connecting MicroPeckerX CAN FD Analyzer to operation and log analysis.

1. Connect devices​

Connect MicroPeckerX.

Use the included USB cable to connect MicroPeckerX to a USB port on your Windows PC.
Also connect MicroPeckerX to the CAN bus.

PC and MPX connection
Notes
  • Incorrect wiring may damage both MicroPeckerX and the target device.
  • If MicroPeckerX is used through a USB hub, PC power alone may be insufficient and operation may become unstable.
    Use a self-powered USB hub.

2. Launch GUI​

Start the GUI application as follows.

  1. Open Windows Start menu
  2. Expand All apps -> MicroPeckerX
  3. Click MicroPeckerX Control Software -> MicroPeckerX Control Software Ver.X.XX (X.XX = product version)
GUI launch

Toolbar​

You can freely arrange the toolbar and each window layout. Adjust to your monitor size.

GUI header

Save/switch window layouts​

You can save window layouts with names and recall them any time.

  • Layout names can be edited/deleted later.
  • Pre-register frequently used layouts to improve efficiency.
  1. Save layout
Window -> Layout -> Save Current Layout
Save menu
  1. Name and save
    Enter a layout name in the dialog and click Save.
Save dialog
  1. Recall saved layout
    Select layout from layout dropdown. You can also save from the adjacent button.
Layout switch

3. Configure communication​

Configure communication settings for MicroPeckerX CAN FD Analyzer.

  1. Open Device Window from menu/toolbar.
Communication settings
  1. Baud rate / sample point
  • CAN: communication speed (e.g., 500 kbps)
  • CAN FD: payload speed and sample point
  1. ACK response
  • Enable/disable ACK response from MicroPeckerX
  1. Termination resistor
  • Set bus termination ON/OFF

4. Configure display​

Set label display to make communication results easier to read. Skip if unnecessary.

Label filter example​

With label filters, label names and colors are applied for better visibility.

Label target IDLabel nameBackground color
011Sample1green
012Sample2blue
013Sample3yellow
Before label filter​
Before label filter
After label filter​
After label filter

Label filter setup​

  1. Open Label Filter Window from menu/toolbar.
Label Filter Window
  1. Add filter with + button.

  2. Configure label appearance

  • Double-click label field [1] in Filter Setting, or click pencil icon
  • Set font/background color in dialog
  1. Configure filter conditions
  • Double-click condition field [2], or click pencil icon
  • Set frame conditions and click OK

After this, colored labels are added to logs so target frames can be identified quickly.


5. Select operation mode​

Select operation mode of MicroPeckerX CAN FD Analyzer.

Operation mode
  1. Open Simulation Window from menu/toolbar.

  2. Select Simulation Mode

Simulation ModeDescription
NoneMonitor-only mode. No frame transmission.
Send FramePeriodic transmission and event-based transmission can be configured.
Log ReplayTransmits frames based on prepared transmission logs.
BurstTransmitPerforms continuous high-load transmission on bus.

For details, see the simulation section.


6. Start operation​

Click toolbar ▶ to start operation.
When started, window layout automatically switches for monitoring logs.

Before start​
Before start
During monitoring​
During monitoring
  1. Click ▶
  2. Layout switches and communication logs are displayed

7. Stop operation​

Click toolbar ■ to stop communication.
After stop, layout switches to log-review friendly view.

After stop​
After stop
  1. Click ■
  2. Layout switches to log review view

8. Check and analyze logs​

After stopping, you can display and process recorded logs.
This section introduces search and offset functions.

Other analysis functions are also available:

  • Frame Cycle Analyze: visualize/analyze frame transmission intervals
  • CAN Gateway Latency: measure gateway delay and message loss
  • CAN Gateway Residence: check peak gateway residence time

Search function​

To find specific frames, specify IDs in the search box.
Partial match is supported. For example, searching *01 highlights frame 0x001.

  1. Open Log Search tab and click pencil button to open Log Search dialog
  2. Enter *01 in ID field
  3. Click OK
  4. Click Backward or Forward to select/highlight matched frames
Before search After search

Offset function​

Use offset function to confirm transmission intervals and relative time.

  1. Right-click the frame to use as reference
  2. Select Set Offset from context menu
  3. Other frames are shown with relative time from reference timestamp
Before offset​
Before offset
After offset​
After offset

This allows intuitive understanding of inter-frame intervals with any frame as the reference point.